---
title: "Insert Molding Services | Threaded Inserts & Metal | OpenSpindle"
description: "Get insert molding quotes from qualified manufacturing partners. Metal inserts such as threaded bosses, pins, and terminals are loaded into the tool and plastic is molded around them, integrating metal and plastic in a single molded part."
canonical: https://openspindle.com/capabilities/insert-molding
---

# Get quotes for custom insert molded parts

Metal inserts such as threaded bosses, pins, or terminals are loaded into the mold before the shot, and plastic is molded around them. That integrates metal and plastic into one part in a single step, with stronger retention than a part where the insert is added afterward. Upload your part and we'll source competitive quotes from qualified manufacturing partners.

## How to design for Insert Molding

Insert molding adds a few extra design rules on top of standard injection molding, mostly around protecting the insert and the plastic around it.

| Design rule | Typical spec | Why |
| --- | --- | --- |
| Wall around the insert | >= 0.5x insert diameter | Thin plastic around an insert cracks under molding stress or in service. |
| Insert retention features | knurl, undercut, or groove | A smooth insert can spin or pull out; a mechanical lock keeps it in place. |
| Insert preheat | recommended for larger inserts | Warming the insert before molding reduces thermal shock and stress cracking around it. |
| Insert position tolerance in the tool | tight, fixture-dependent | The insert must seat in the same spot every cycle or the wall around it goes uneven. |
| Draft angle | >= 1 to 2 degrees per side | Standard molding draft still applies to the plastic body around the insert. |

Insert molding rules build on standard injection molding design rules. A shop confirms insert placement and retention for your specific part and material.

## Insert molding vs alternatives

Insert molding is not always the right way to combine metal and plastic. Here is when another approach fits better.

| Process | Best for | Typical volume | Choose it over Insert Molding when |
| --- | --- | --- | --- |
| Post-mold inserts (heat-set or ultrasonic) | Low volume, evolving design | Prototype to low volume | Installing inserts after molding is more flexible and lower tooling risk when your volume is low or the design is still changing. |
| [Overmolding](https://openspindle.com/capabilities/overmolding.md) | Adding a second polymer layer | Low to high | You are adding a second polymer layer, like a soft-touch grip, rather than a rigid or metal insert. |
| [Injection Molding](https://openspindle.com/capabilities/injection-molding.md) | Single-material plastic parts | 1,000+ | Your part does not need a metal insert at all; standard single-material molding is the simpler baseline. |

## Industries Served

- Electronics
- Automotive
- Medical devices
- Consumer products
- Industrial / OEM

Insert molding shows up wherever a molded plastic part needs a metal fastening point, contact, or wear surface built in.

## Frequently Asked Questions

### What is insert molding?

Insert molding is an injection molding process where a metal (or sometimes plastic or ceramic) insert, such as a threaded boss, pin, or terminal, is loaded into the mold before the shot. Plastic is then molded around it, bonding the two into a single part in one step instead of assembling them afterward.

### Insert molding vs heat-set inserts, which should I use?

Heat-set (or ultrasonic) inserts are pressed or melted into a plastic part after it is molded, which is cheaper to set up and easier to change as your design evolves. Insert molding places the insert during the molding shot itself, giving stronger retention and a cleaner part, but it needs tooling built around loading and holding the insert. Heat-set inserts suit low volume and prototyping; insert molding pays off at higher volume with a locked-in design.

### What kinds of inserts can be molded in?

The most common are threaded metal bosses for fasteners, brass or steel pins, and electrical contacts or terminals. Inserts are typically brass, stainless steel, or another metal, though the process can also mold in ceramic or a dissimilar plastic component, as long as it can survive the injection pressure and heat of the shot.

### How are inserts held in the tool during molding?

Inserts are placed into fixtured pockets or pins in the mold, either by hand for lower volumes or automatically for production, before the tool closes and the shot is injected. The fixturing controls the insert position tolerance in the tool so it lands in the same spot every cycle, and the plastic wall thickness around it is designed to survive the clamping and injection forces without cracking.

### Insert molding vs overmolding, what is the difference?

Insert molding embeds a metal (or other non-plastic) component inside a plastic part during the shot. Overmolding is molding one polymer over another, such as a soft TPU grip over a rigid nylon substrate, usually to add feel, seal, or a soft surface. Some parts use both: an insert-molded structural component that is then overmolded with a soft layer.

### How much does insert molding cost compared to standard injection molding?

Insert molding typically costs somewhat more than standard injection molding because the tool needs fixturing to hold and locate the insert, and the molding cycle often includes a manual or automated insert-loading step. The tradeoff is a stronger, single-step part versus assembling the insert afterward. Upload your part and volume to see real pricing from qualified molding partners.

## Other Capabilities

- [Injection Molding](https://openspindle.com/capabilities/injection-molding.md)
- [Overmolding](https://openspindle.com/capabilities/overmolding.md)
- [Prototype Molding](https://openspindle.com/capabilities/prototype-molding.md)
- [CNC Machining](https://openspindle.com/capabilities/cnc-machining.md)

## Get insert molding quotes

Upload your part and get insert molding pricing from qualified manufacturing partners set up to mold plastic around metal inserts.