---
title: "Countersink & Counterbore Chart: Inch and Metric Screws | OpenSpindle"
description: "Countersink diameter and angle for inch and metric flat head screws, plus counterbore diameter and depth for socket head cap screws, #4 to 1/2 and M3 to M12."
canonical: https://openspindle.com/reference/countersink-chart
---

# Countersink and Counterbore Chart

Head diameters, angles, clearance holes and counterbore sizes for common inch and metric flat head and socket head cap screws, from #4 to 1/2 in and M3 to M12.

A countersink is sized by its diameter at the surface and its included angle, which must match the screw head: 82 degrees for inch flat heads and 90 degrees for metric. Cut the countersink to about the maximum head diameter for a flush head, slightly larger for a head below flush. A counterbore is sized by diameter and depth: larger than the head, and at least as deep as the head height. Values below come from the published head dimensions; confirm against your fastener specification.

## Inch flat head socket cap screws (82°)

Hex socket flat countersunk head cap screws to ASME B18.3. The maximum head diameter is the theoretical sharp-edge value; the minimum is the actual head after the edge flat. For a flush head, countersink to the maximum diameter. Add about 0.005 to 0.015 in to sit the head slightly below the surface.

| Screw size | Included angle | Head dia max, sharp (in) | Head dia min (in) | Head height, ref (in) | Clearance drill, normal fit (in) |
| --- | --- | --- | --- | --- | --- |
| #4 | 82° | 0.255 | 0.218 | 0.082 | #29 (0.136) |
| #6 | 82° | 0.307 | 0.263 | 0.097 | #18 (0.170) |
| #8 | 82° | 0.359 | 0.311 | 0.112 | #10 (0.194) |
| #10 | 82° | 0.411 | 0.359 | 0.127 | #2 (0.221) |
| 1/4 | 82° | 0.531 | 0.480 | 0.162 | 9/32 (0.281) |
| 5/16 | 82° | 0.656 | 0.600 | 0.198 | 11/32 (0.344) |
| 3/8 | 82° | 0.781 | 0.720 | 0.234 | 13/32 (0.406) |
| 7/16 | 82° | 0.844 | 0.781 | 0.234 | 15/32 (0.469) |
| 1/2 | 82° | 0.938 | 0.872 | 0.252 | 17/32 (0.531) |

*Head height is a reference value calculated from the sharp head diameter and the 82° angle. Slotted and cross recessed flat head machine screws (ASME B18.6.3) are also 82° but have different head diameters; check their table before sizing.*

## Metric countersunk socket screws (90°)

Hexagon socket countersunk head screws to ISO 10642. The theoretical head diameter is 2.24 times the thread diameter; the actual head is smaller because of the edge flat. Countersink to the theoretical diameter for a flush head, or about 0.2 to 0.4 mm over it to sit slightly below. Clearance holes are ISO 273 medium series.

| Screw size | Included angle | Head dia, theoretical max (mm) | Head dia, actual min (mm) | Head height max (mm) | Clearance hole, medium (mm) |
| --- | --- | --- | --- | --- | --- |
| M3 | 90° | 6.72 | 5.54 | 1.86 | 3.4 |
| M4 | 90° | 8.96 | 7.53 | 2.48 | 4.5 |
| M5 | 90° | 11.20 | 9.43 | 3.10 | 5.5 |
| M6 | 90° | 13.44 | 11.34 | 3.72 | 6.6 |
| M8 | 90° | 17.92 | 15.24 | 4.96 | 9.0 |
| M10 | 90° | 22.40 | 19.22 | 6.20 | 11.0 |
| M12 | 90° | 26.88 | 23.12 | 7.44 | 13.5 |

*Slotted and cross recessed metric countersunk screws (ISO 2009, ISO 7046) are also 90° but have different head sizes.*

## Inch socket head cap screw counterbores

Socket head cap screws to ASME B18.3. Counterbore diameters are common shop and design values, about 1/32 to 1/16 in larger than the head. A depth of the head height plus 0.010 to 0.030 in sets the head just below the surface; add more if a washer goes under the head.

| Screw size | Head dia max (in) | Head height max (in) | Clearance drill, close fit (in) | Clearance drill, normal fit (in) | Counterbore dia (in) | Counterbore depth, typical (in) |
| --- | --- | --- | --- | --- | --- | --- |
| #4 | 0.183 | 0.112 | 1/8 (0.125) | #29 (0.136) | 7/32 (0.219) | 0.122 to 0.142 |
| #6 | 0.226 | 0.138 | #23 (0.154) | #18 (0.170) | 9/32 (0.281) | 0.148 to 0.168 |
| #8 | 0.270 | 0.164 | #15 (0.180) | #10 (0.194) | 5/16 (0.312) | 0.174 to 0.194 |
| #10 | 0.312 | 0.190 | #5 (0.206) | #2 (0.221) | 3/8 (0.375) | 0.200 to 0.220 |
| 1/4 | 0.375 | 0.250 | 17/64 (0.266) | 9/32 (0.281) | 7/16 (0.438) | 0.260 to 0.280 |
| 5/16 | 0.469 | 0.312 | 21/64 (0.328) | 11/32 (0.344) | 17/32 (0.531) | 0.322 to 0.342 |
| 3/8 | 0.562 | 0.375 | 25/64 (0.391) | 13/32 (0.406) | 5/8 (0.625) | 0.385 to 0.405 |
| 7/16 | 0.656 | 0.438 | 29/64 (0.453) | 15/32 (0.469) | 23/32 (0.719) | 0.448 to 0.468 |
| 1/2 | 0.750 | 0.500 | 33/64 (0.516) | 17/32 (0.531) | 13/16 (0.812) | 0.510 to 0.530 |

*Close fit holds position better between mating parts; normal fit is the usual default and tolerates more hole position error.*

## Metric socket head cap screw counterbores

Socket head cap screws to ISO 4762. Counterbore diameters are common design values for this head (similar to DIN 974-1 recommendations). A depth of the head height plus about 0.3 to 0.8 mm sets the head below the surface. Clearance holes are ISO 273 fine and medium series.

| Screw size | Head dia max (mm) | Head height max (mm) | Clearance hole, fine (mm) | Clearance hole, medium (mm) | Counterbore dia (mm) | Counterbore depth, typical (mm) |
| --- | --- | --- | --- | --- | --- | --- |
| M3 | 5.50 | 3.00 | 3.2 | 3.4 | 6.5 | 3.3 to 3.8 |
| M4 | 7.00 | 4.00 | 4.3 | 4.5 | 8.0 | 4.3 to 4.8 |
| M5 | 8.50 | 5.00 | 5.3 | 5.5 | 10.0 | 5.3 to 5.8 |
| M6 | 10.00 | 6.00 | 6.4 | 6.6 | 11.0 | 6.3 to 6.8 |
| M8 | 13.00 | 8.00 | 8.4 | 9.0 | 15.0 | 8.3 to 8.8 |
| M10 | 16.00 | 10.00 | 10.5 | 11.0 | 18.0 | 10.3 to 10.8 |
| M12 | 18.00 | 12.00 | 13.0 | 13.5 | 20.0 | 12.3 to 12.8 |

*Low head socket cap screws (DIN 7984 and similar) have shorter heads and need shallower counterbores. Check the head height for the exact screw you use.*

## Countersink angles by fastener type

| Fastener | Included angle |
| --- | --- |
| Inch flat head screws (ASME B18.3, B18.6.3) | 82° |
| Metric countersunk screws (ISO 10642, ISO 2009, ISO 7046) | 90° |
| Aerospace countersunk rivets and screws (for example MS20426 rivets) | 100° |
| Center holes and deburr chamfers (not a screw seat) | 60° or 90° |

## Drawing callout examples

ASME Y14.5 uses ⌵ for a countersink, ⌴ for a counterbore and ↧ for depth.

| Feature | Example callout |
| --- | --- |
| Countersink, #10 flat head, flush | ⌀.221 THRU, ⌵ ⌀.411 X 82° |
| Countersink, M6 flat head, slightly below flush | ⌀6.6 THRU, ⌵ ⌀13.7 X 90° |
| Counterbore, 1/4 socket head cap screw | ⌀.281 THRU, ⌴ ⌀.438 ↧ .270 |
| Counterbore, M8 socket head cap screw | ⌀9 THRU, ⌴ ⌀15 ↧ 8.6 |

*Dimension countersinks by surface diameter and angle rather than depth; the diameter decides flushness and can be checked with a countersink gauge.*

Values are typical clearance and design values derived from the published head dimensions in ASME B18.3, ISO 10642 and ISO 4762, and the ISO 273 clearance hole series. Head dimensions vary by standard, head style and manufacturer; confirm against the fastener specification you buy to. In thin sheet, a machined countersink may not leave enough material below the cone, so check thickness against head height.

## On OpenSpindle

- [Countersink vs counterbore](https://openspindle.com/blog/countersink-vs-counterbore.md)
- [Drill size chart](https://openspindle.com/reference/drill-size-chart.md)
- [GD&T symbols reference](https://openspindle.com/reference/gdt-symbols-reference.md)
- [CNC machining](https://openspindle.com/capabilities/cnc-machining.md)

## Frequently asked questions

### What size countersink do I need for a #10 flat head screw?

For an inch #10 hex socket flat head screw to ASME B18.3, countersink to about 0.411 in diameter at 82 degrees for a flush head, slightly larger to sit below flush. Use a #2 (0.221 in) normal-fit clearance hole.

### What size countersink for an M6 flat head screw?

For an M6 countersunk socket screw to ISO 10642, countersink to about 13.4 mm diameter at 90 degrees for a flush head, about 13.6 to 13.8 mm to sit slightly below. A 6.6 mm medium clearance hole is typical.

### How deep should a counterbore be?

At least the screw head height, plus a small allowance so the head sits below the surface: typically 0.010 to 0.030 in for inch screws or 0.3 to 0.8 mm for metric. For a socket head cap screw the head height equals the thread diameter, so an M8 counterbore is about 8.3 to 8.8 mm deep.

### Is a countersink 82 or 90 degrees?

Inch flat head screws use 82 degrees; metric countersunk screws use 90 degrees. Aerospace countersunk fasteners commonly use 100 degrees. Match the angle to the screw standard and state it on the drawing.
