The short answer
A stress concentration is a local spike in stress at a hole, notch, sharp corner, shoulder or thread, measured by the stress concentration factor Kt: peak stress divided by nominal stress. A small hole in a plate under tension has a Kt of about 3. Stress raisers matter most in fatigue, where most cracks start at one. Generous radii, well-placed holes and good surface finish are the main fixes.
What a stress concentration is
Load flows through a part the way water flows through a channel. Where the cross-section is uniform, stress is spread evenly. Where the geometry changes abruptly, at a hole, a notch, a sharp inside corner, a step in a shaft or a thread root, the load lines crowd together and the local stress rises well above the average.
That local peak is a stress concentration, and the feature that causes it is a stress raiser (or stress riser). The size of the effect is the stress concentration factor, Kt:
Kt = peak local stress / nominal stress
Nominal stress is what you would calculate from simple formulas, such as load divided by area. A Kt of 3 means the edge of the feature sees three times that stress. Kt depends only on geometry and loading type (tension, bending or torsion), not on the material, which is why it can be read from charts.
The practical lesson is simple: the sharper the feature relative to its size, the higher the peak. Radius is the cheapest strength you can add to a part.
Typical Kt values for common features
Exact values come from Peterson's Stress Concentration Factors, which charts Kt for hundreds of geometries, or from finite element analysis. These typical values are useful for judging which features matter.
| Feature | Loading | Typical Kt | Notes |
|---|---|---|---|
| Small round hole in a wide plate | Tension | About 3.0 | Classic result, based on the gross stress away from the hole. Falls toward about 2 (on net-section stress) as the hole gets large relative to plate width. |
| Elliptical hole, long axis across the load | Tension | 1 + 2a/b | a is the half-width across the load and b the half-width along it. A slot twice as long as it is wide gives about 5. |
| Crack or very sharp notch | Tension or bending | Very high, rising as the tip radius shrinks | Roughly 1 + 2 times the square root of notch depth over tip radius. This is why scratches and sharp tool marks start fatigue cracks. |
| Shaft shoulder, sharp fillet (r/d about 0.02) | Bending / torsion / axial | About 2.7 / 2.2 / 3.0 | Typical first-pass estimates for a shoulder with a D/d around 1.5 to 2. |
| Shaft shoulder, well-rounded fillet (r/d about 0.1) | Bending / torsion / axial | About 1.7 / 1.5 / 1.9 | Same shoulder with a fillet five times larger. |
| End-milled keyseat | Bending / torsion | About 2.1 / 3.0 | Corner radius about 2 percent of shaft diameter. |
| Retaining ring groove | Bending / torsion / axial | About 5.0 / 3.0 / 5.0 | Sharp-bottomed grooves are among the worst common features. |
| Thread root, rolled vs cut (steel bolt, SAE grade 5 to 8) | Fatigue, axial | Kf about 3.0 rolled, 3.8 cut | These are fatigue factors (Kf), already including notch sensitivity. Rolled threads are better because the root is formed, not cut, and left in compression. |
Typical values compiled from Peterson's charts and standard machine design texts. Real Kt depends on exact proportions; use the charts or FEA for design.
Static loads versus fatigue
A stress concentration matters very differently depending on how the part is loaded and what it is made of.
Static load, ductile material. When the peak exceeds yield, a small zone at the notch yields and the load redistributes to the surrounding material. For a steel or aluminum bracket that sees a steady load, designers often check the net-section stress and do not apply Kt to the strength calculation.
Static load, brittle material. Glass, ceramics, some cast alloys, hardened tool steel and many cast or filled plastics do not yield first. The peak stress at the notch is the stress that breaks the part, so Kt applies in full.
Fatigue. Under repeated loading, even ductile metals crack at stress raisers, because each cycle concentrates damage at the same small spot. A large share of mechanical failures in service are fatigue failures, and most of them start at a feature: a hole, a fillet, a thread, a weld toe or a surface scratch.
For fatigue, engineers use the fatigue stress concentration factor Kf = 1 + q (Kt - 1), where q is the notch sensitivity, between 0 and 1. Higher-strength steels are more notch sensitive (q closer to 1), and very small notch radii tend to have lower q. The practical takeaway: in fatigue-loaded parts, every sharp feature costs life, and stronger materials are less forgiving of them, not more.
Inside corner radii, tied to what each process can cut
The most common stress raiser a buyer controls is the inside corner. The right radius depends on how the part will be made, because each process leaves a different minimum.
| Process | Smallest inside corner it leaves | What to put on the drawing |
|---|---|---|
| CNC milling, vertical walls | The end mill radius, commonly 1.5 to 6 mm (1/16 to 1/4 in) on pocket corners | A radius slightly larger than a standard cutter radius, for example 3.2 mm for a 6 mm (1/4 in) tool, so the tool arcs through the corner instead of stopping in it. Larger is cheaper and stronger. |
| CNC milling, pocket floor to wall | Near sharp with a flat end mill | If the floor corner is loaded, specify a floor fillet; the shop uses a bull-nose or ball end mill. |
| CNC turning, shoulders | The insert nose radius, commonly 0.4 or 0.8 mm (1/64 or 1/32 in) | A shoulder fillet radius on the drawing, and an undercut only where a mating part has to seat square. |
| Fiber laser | About half the kerf, near sharp | Draw a radius in the DXF on loaded corners, typically at least 0.5 to 1 mm, or larger in thick plate. The laser will cut a sharp corner if you draw one. |
| Abrasive waterjet | About 0.4 to 0.6 mm | A drawn radius at or above that, larger on fatigue-loaded parts. |
| Plasma | About 1 to 2 mm, with a heat-affected edge | Generous radii. For fatigue-critical parts, consider machining the edge after cutting. |
| Sheet metal bend relief | A rectangular relief leaves two sharp corners | Bend reliefs with a rounded end (obround or teardrop), relief width at least the material thickness, so the corner of the relief is not a crack starter. |
| Wire EDM | Wire radius plus spark gap, about 0.07 to 0.18 mm | A radius where the part will see cyclic load; EDM can cut very small radii, which does not mean the part should have them. |
Typical values. Tooling varies by shop and material.
Holes: edge distance and placement
A hole is a stress raiser by itself, and a hole near an edge or another hole is worse, because the stress fields overlap and the thin ligament between them carries the load.
Typical guidance:
- Fastener holes in loaded parts: keep the center of the hole at least 1.5 to 2 hole diameters from the edge in the direction of load. Aerospace practice commonly uses 2 diameters. Less than that and the hole can tear out.
- Sheet metal: keep holes at least 2 material thicknesses from an edge and from a bend, to avoid both distortion and a weak ligament. The sheet metal DFM guide covers the forming side.
- Hole-to-hole spacing: keep at least one hole diameter of material between hole edges where the plate is loaded.
- Placement: in a beam or bracket loaded in bending, stress is highest at the outer fibers and near zero at the neutral axis. Put holes, slots and cable pass-throughs near the neutral axis and away from the highest-moment region, typically near the support of a cantilever.
Cross holes in shafts deserve particular care. A radial hole for a pin or oil passage in a rotating shaft is a significant stress raiser in bending and torsion, and it is a classic fatigue origin. Locate it away from shoulders and keyways, break its edges, and confirm its effect with the charts.
Shoulders, threads and grooves
Shafts and turned parts concentrate several stress raisers in a small space. A few rules cover most of them:
- Give every shoulder a fillet. The jump from Kt about 2.7 to about 1.7 in the table above comes from changing the fillet from 2 percent to 10 percent of the smaller diameter. If a bearing or gear needs a sharp shoulder to seat against, use a relief groove behind the shoulder or a spacer with a chamfer, so the fillet can stay large.
- Reduce the step. A smaller ratio between the large and small diameters lowers Kt. Where the step has to be large, a tapered transition or a relief groove helps.
- Keep threads out of high-stress zones. Thread roots are among the sharpest features on a part. Put threads where the bending moment is low, add a thread relief so the thread does not run into a shoulder, and specify rolled threads on fatigue-loaded fasteners. See the thread callout guide for how to call them out.
- Avoid stacking features. A keyway ending at a shoulder fillet, or a cross hole next to a retaining ring groove, multiplies risk. Separate them along the axis.
- Watch retaining ring grooves. With a typical Kt near 5 in bending, they belong in low-stress locations only.
Surface finish and edge condition
Fatigue cracks start at the surface, so surface condition acts like a field of tiny stress raisers. Machine design texts capture this with a surface factor that reduces the endurance limit. Typical values for a steel with about 600 MPa (87 ksi) tensile strength:
| Surface condition | Typical surface factor (fraction of polished-specimen endurance limit) |
|---|---|
| Ground | About 0.9 |
| Machined or cold drawn | About 0.8 |
| Hot rolled | About 0.6 |
| As forged | About 0.45 |
Typical values from the Marin surface factor equation in standard machine design texts. The penalty grows with tensile strength, so high-strength steels lose more to a rough surface.
Finish and edge choices that help fatigue life
Beyond the surface factor, a few process choices are worth calling out on the drawing for parts that see cyclic load:
- Specify surface roughness on fatigue-critical features, such as fillets, bores and the faces of a rotating shaft, rather than relying on the general finish note. The surface roughness chart shows typical Ra by process.
- Orient tool marks along the load where you can. A polish or a finishing pass in the load direction removes marks that run across it.
- Treat thermal-cut edges. Laser, plasma and oxyfuel edges carry a heat-affected zone and sometimes a hardened recast layer and micro-notches. For fatigue-critical parts, ask for edges to be machined, ground or deburred, or specify waterjet, which leaves no heat-affected zone.
- Consider shot peening for springs, gears, shafts and welded structures. It leaves a thin layer of compressive residual stress that resists crack initiation.
- Break sharp edges with a specified chamfer or radius. "Break all edges 0.2 to 0.5 mm" is a clear, inexpensive note.
- Be careful with coatings. Some processes, such as hard anodizing and certain electroplates, can reduce fatigue strength. If the part is fatigue critical, tell the shop so the finish can be chosen with that in mind.
What to put on the RFQ
A shop will cut the radius you draw. If it matters, draw it and dimension it. For parts where stress concentration is a real concern:
- Dimension critical fillet and corner radii, with a minimum rather than a nominal where that is what you mean (for example R1.5 MIN)
- Note fatigue-critical surfaces and their roughness, and any peening or edge treatment
- Say whether thermal cutting is acceptable on loaded edges
- Specify rolled threads where you need them
- Tell the shop how the part is loaded, in one line, so it can flag a feature that looks risky
Upload the STEP and drawing at openspindle.com/quote. The matched shop reviews manufacturability as part of the quote and comes back with one price, usually in about 24 hours.
Sources
- Pilkey and Pilkey, Peterson's Stress Concentration Factors, 3rd edition (Wiley)
- Budynas and Nisbett, Shigley's Mechanical Engineering Design (McGraw-Hill)
- ASM Handbook, Volume 19: Fatigue and Fracture
Last reviewed by Tom Petrini