Tube Bend Radius Chart
Centerline radius by tube size, wall factor and mandrel guidance, outer wall thinning, and nominal pipe size to real OD, for designing bent tube parts that match standard tooling.
STEP · STL · IGES · DWG · DXF · SLDPRT · and more
No CAD file? Describe your project instead
Tube bend radius is measured to the centerline of the tube and called the centerline radius, or CLR. Shops express it as a multiple of the tube's outside diameter (OD), the D of bend: a 2D bend on 1 in OD tube has a 2 in CLR. Each OD and CLR pair needs its own bend die, so designing to a radius the shop already owns is the cheapest choice. For most tube sizes, 2D and 3D are the safest defaults.
Centerline radius by tube OD
CLR at common D-of-bend multiples. 2D and 3D dies are widely stocked; 1D and 1.5D usually mean a mandrel and wiper die. Confirm the shop's die list before you lock the radius.
| Tube OD (in) | Tube OD (mm) | 1D CLR (in) | 1.5D CLR (in) | 2D CLR (in) | 3D CLR (in) |
|---|---|---|---|---|---|
| 0.250 | 6.4 | 0.25 | 0.375 | 0.50 | 0.75 |
| 0.375 | 9.5 | 0.375 | 0.5625 | 0.75 | 1.125 |
| 0.500 | 12.7 | 0.50 | 0.75 | 1.00 | 1.50 |
| 0.625 | 15.9 | 0.625 | 0.9375 | 1.25 | 1.875 |
| 0.750 | 19.1 | 0.75 | 1.125 | 1.50 | 2.25 |
| 1.000 | 25.4 | 1.00 | 1.50 | 2.00 | 3.00 |
| 1.250 | 31.8 | 1.25 | 1.875 | 2.50 | 3.75 |
| 1.500 | 38.1 | 1.50 | 2.25 | 3.00 | 4.50 |
| 1.750 | 44.5 | 1.75 | 2.625 | 3.50 | 5.25 |
| 2.000 | 50.8 | 2.00 | 3.00 | 4.00 | 6.00 |
| 2.500 | 63.5 | 2.50 | 3.75 | 5.00 | 7.50 |
| 3.000 | 76.2 | 3.00 | 4.50 | 6.00 | 9.00 |
CLR = D of bend x tube OD. Shops often stock nearby radii rather than exact multiples (for example a 3.5 in die for 1.75 in tube), so ask before dimensioning.
Wall factor and when a mandrel is needed
Wall factor is tube OD divided by wall thickness: 1.5 in OD with a 0.120 in wall is a wall factor of 12.5. A tight radius (small D of bend) on a thin wall (large wall factor) is the hard case and needs inside support to stop wrinkling and collapse.
| D of bend | Wall factor | Typical tooling |
|---|---|---|
| 3D or larger | Under about 10 | Often no mandrel (empty bending) |
| About 2D to 3D | About 10 to 20 | Plug or single-ball mandrel |
| About 1.5D to 2D | About 20 to 40 | Multi-ball mandrel, often with a wiper die |
| Under 1.5D | Any thin wall | Multi-ball mandrel and wiper die; confirm with the shop first |
Starting points for rotary draw bending in steel and aluminum. Material, machine and tooling move these boundaries, and harder alloys need more support than the table suggests.
Outer wall thinning by D of bend
The outside of a bend stretches and thins. An idealized estimate of the thinning is 1 / (2D + 1) of the original wall. Neutral axis shift and pressure die boost usually keep real thinning below these numbers, but check the thinned wall for tubes that carry pressure.
| D of bend | Estimated outer wall thinning |
|---|---|
| 1D | About 33% |
| 1.5D | About 25% |
| 2D | About 20% |
| 2.5D | About 17% |
| 3D | About 14% |
| 4D | About 11% |
| 5D | About 9% |
Bendability by material
Temper and tube type matter as much as the alloy family. These are general tendencies; the shop confirms against its own experience with your size.
| Material | Bending notes |
|---|---|
| Mild steel, DOM | Bends well; uniform wall, the usual choice for tight bends and structural frames |
| Mild steel, ERW | Bends well; place the weld seam near the bend's neutral axis |
| 4130 chromoly | Bends well; more springback than mild steel |
| Stainless 304 / 316 | Work hardens and springs back more; needs good lubrication and often a mandrel |
| Aluminum 6061-T6 | Cracks on tight bends; 3D or larger is a safer default |
| Aluminum 6063, 3003, 5052 | Bend much more easily than 6061-T6 |
| Copper, brass (annealed) | Bend easily; thin walls still kink without support |
| Titanium Grade 2 | Bends cold with care and generous radii |
| Titanium Grade 5 | Hard to bend cold; usually needs a large radius or heat |
Nominal pipe size to outside diameter
Pipe is sold by nominal pipe size (NPS) and schedule, and the nominal size is not the OD. Bend dies are made to the real OD, so give the OD and wall, or the exact NPS and schedule.
| NPS | OD (in) | Sch 40 wall (in) | Sch 80 wall (in) |
|---|---|---|---|
| 1/2 | 0.840 | 0.109 | 0.147 |
| 3/4 | 1.050 | 0.113 | 0.154 |
| 1 | 1.315 | 0.133 | 0.179 |
| 1-1/4 | 1.660 | 0.140 | 0.191 |
| 1-1/2 | 1.900 | 0.145 | 0.200 |
| 2 | 2.375 | 0.154 | 0.218 |
| 2-1/2 | 2.875 | 0.203 | 0.276 |
| 3 | 3.500 | 0.216 | 0.300 |
Dimensions per ASME B36.10M for carbon steel pipe. Stainless pipe in the same sizes shares these ODs.
Straight length and typical tolerances
The clamp die needs straight tube between bends, and accuracy is set per bend, then accumulates across the part.
| Item | Typical value |
|---|---|
| Straight between bends | At least 1.5 to 2 x OD; under about 1 x OD needs special tooling |
| Bend angle | About +/- 0.5 to 1 degree |
| Length between bends | About +/- 0.5 to 1.5 mm (0.02 to 0.06 in) |
| Ovality | Specify as a percent of OD only where a part slides over the bend |
Tolerances vary by shop, machine, material and part length. Errors stack across multiple bends, so dimension critical ends to each other.
Values reflect common rotary draw bending practice. A shop confirms radius, mandrel needs and tolerances against its own tooling and your material.
Get a quote for your part
Upload your drawing and we match it with an independent shop and send you one quote, kept under a budget you set.
- Free quote in about 24 hours
- No minimum order
- No account needed to start
STEP · STL · IGES · DWG · DXF · SLDPRT · and more
No CAD file? Describe your project instead
Frequently asked questions
What is the minimum bend radius for tubing?
A centerline radius of two to three times the tube's outside diameter (2D to 3D) bends cleanly in most steel and aluminum tube. Radii down to about 1D are possible with a mandrel and wiper die. Thin walls and hard tempers such as 6061-T6 need larger radii.
What is centerline radius in tube bending?
Centerline radius (CLR) is the bend radius measured to the center of the tube, not to its inside or outside surface. Bend dies are specified by CLR, so it is the radius to put on the drawing.
How do I calculate wall factor?
Divide the tube's outside diameter by its wall thickness. A 2 in OD tube with a 0.065 in wall has a wall factor of about 31. Higher wall factors mean thinner walls relative to the tube size, which need more support from a mandrel on tight bends.
Is 1 inch pipe 1 inch in diameter?
No. 1 in nominal pipe has an outside diameter of 1.315 in, and the wall depends on the schedule: 0.133 in for Schedule 40 and 0.179 in for Schedule 80. Tube, by contrast, is sized by its real outside diameter.
Last reviewed by Tom Petrini